To mix things up and provide you with the tools to better navigate your existing business or start a new one, we will be sending out a bi-monthly dispatch — 3,2,1 housing our 3 most viewed articles, 2 of our personal favorites, and 1 of our oldies but goodies that resonated with a lot of readers. Your donation powers our service to the FOSS community. OSUOSL © 2020 © 2020.
- Business Lab For Pages 3 2 1/2
- Business Lab For Pages 3 2 1000
- Business Lab For Pages 3 2 1st
- Business Lab For Pages 3 2 12
3.2.1.8 Packet Tracer – Configuring RIPv2
Packet Tracer – Configuring RIPv2 (Answer Version)
Answer Note: Red font color or Gray highlights indicate text that appears in the Answer copy only.
Topology
Objectives
![For For](https://cdn-wp.labster.com/wp-content/uploads/2019/11/04211953/Lab-Safety-3-e1566568115540-768x509.jpg)
Part 1: Configure RIPv2
Business Lab For Pages 3 2 1/2
Part 2: Verify Configurations
Background
![Lab Lab](https://www.macbed.com/wp-content/uploads/2017/10/40919.png)
Although RIP is rarely used in modern networks, it is useful as a foundation for understanding basic network routing. In this activity, you will configure a default route, RIP version 2, with appropriate network statements and passive interfaces, and verify full connectivity.
Part 1: Configure RIPv2
Step 1: Configure RIPv2 on R1.
Business Lab For Pages 3 2 1000
- Use the appropriate command to create a default route on R1 for all Internet traffic to exit the network through S0/0/1.
- R1(config)# ip route 0.0.0.0 0.0.0.0 s0/0/1
- Enter RIP protocol configuration mode.
- R1(config)# router rip
- Use version 2 of the RIP protocol and disable the summarization of networks.
- R1(config-router)# version 2
- R1(config-router)# no auto-summary
- Configure RIP for the networks that connect to R1.
- R1(config-router)# network 192.168.1.0
- R1(config-router)# network 192.168.2.0
- Configure the LAN port that contains no routers so that it does not send out any routing information.
- R1(config-router)# passive-interface gig 0/0
- Advertise the default route configured in step 1a with other RIP routers.
- R1(config-router)# default-information originate
- Save the configuration.
Step 2: Configure RIPv2 on R2.
- Enter RIP protocol configuration mode.
- R2(config)# router rip
- Use version 2 of the RIP protocol and disable the summarization of networks.
- R2(config-router)# version 2
- R2(config-router)# no auto-summary
- Configure RIP for the networks directly connected to R2.
- R2(config-router)# network 192.168.2.0
- R2(config-router)# network 192.168.3.0
- R2(config-router)# network 192.168.4.0
- Configure the interface that contains no routers so that it does not send out routing information.
- R2(config-router)# passive-interface gig 0/0
- Save the configuration.
Step 3: Configure RIPv2 on R3
Business Lab For Pages 3 2 1st
Lightcapture 1 0 6. Repeat Step 2 on R3.
R3(config)# router rip
R3(config-router)# version 2
R3(config-router)# no auto-summary
R3(config-router)# network 192.168.4.0
R3(config-router)# network 192.168.5.0
R3(config-router)# passive-interface gig 0/0/0 Iphoto 9 5.
R3(config-router)# version 2
R3(config-router)# no auto-summary
R3(config-router)# network 192.168.4.0
R3(config-router)# network 192.168.5.0
R3(config-router)# passive-interface gig 0/0/0 Iphoto 9 5.
Part 2: Verify Configurations
Step 1: View routing tables of R1, R2, and R3.
- Use the appropriate command to show the routing table of R1. RIP (R) now appears with connected (C) and local (L) routes in the routing table. All networks have an entry. You also see a default route listed.
- View the routing tables for R2 and R3. Notice that each router has a full listing of all the 192.168.x.0 networks and a default route.
Business Lab For Pages 3 2 12
Step 2: Verify full connectivity to all destinations.
Capture one 9 3 0 – raw workflow software. Every device should now be able to ping every other device inside the network. In addition, all devices should be able to ping the Web Server.